GRAPHITE GASKETS
Supplied to a very broad range of graphite gaskets. KLINGER graphite gaskets enjoy excellent reputation as sole sealing material as well as reinforced with stainless steel. Especially with regards to high temperature, pressure and leak-proof requirements, graphite gaskets made by KLINGER are widely regarded as industry benchmark.
KLINGER PSM-AS
Graphite with perforated steel insertion, 3xA self-release surfaces. Purity: 98% alt. 99.85%. Density according to the customer’s requests.
Specifications
- Handles 450°C in continuous operation in combination with high pressure
- Very good against worn flange surfaces
- Perfect for steam
- Does not stick on the flange
- Contains no adhesive
- Perforated steel insertion witch is very resistant to exhaust
- Also available as TA-luft approved in executing TSM
Dimensions, standard paper
- Size: 1000 x 1000 mm
- Thickness: 0.6, 1.0, 1.5, 2.0, 3.0 või 4.0 mm
- Tolerance: Thickness ± 5 %, Length ± 5 mm, Width ± 5 mm
- Also comes delivered as rings in DIN, ANSI and user-defined dimensions
KLINGER SLS-AS
Graphite steel foil insertions, 3xA self-release surfaces. Purity: 98% alt. 99.85%. Density according to the customer’s requests.
Specifications
- Handles 450°C in continuous operation
- Perfect for steam
- Does not stick on the flange
- Can be cut by hand
- Can be ordered in very thin thicknesses
Dimensions, standard paper
- Size: 1000 x 1000 mm
- Thickness: 0.6, 1.0, 1.5, 2.0, 3.0 või 4.0 mm
- Tolerance: Thickness ± 5 %, Length ± 5 mm, Width ± 5 mm
- Also comes delivered as rings in DIN, ANSI and user-defined dimensions
KLINGER MILAM PSS
High-temperature Gasket Material based on Mica with Perforated Stainless Steel Reinforcement.
Specifications
- Specially suitable at aggressive acids and high temperatures up to 900 °C
- Suitable in exhaust pipes, turbines, turbochargers and fuel hoses
- Also suitable above the typical application temperatures of Graphite
- NB! Not suitable in high pressure environment, max 5 bar
Dimensions, standard paper
- Size: 1200 x 1000 mm
- Thickness: 1.3, 2.0 või 3.0 mm
- Tolerance: 1.3 mm – Thickness: ± 5%, 2.0 mm – Thickness: ± 10 %, 3.0 mm – Thickness: ± 10%, Length: ± 5%, Width: ± 5 %
- Also comes in user-defined dimensions
KLINGER K35-TEIP
Graphite Tape, pure graphite. Purity: 98% alt. 99.85%. Density according to the customer’s requests.
Specifications
- Handles temperatures up to 450°C in continuous operation
- Adapts excellent to poor flange surfaces
- Available with and without adhesives
- Handles most type of media
- Adhesive on the exterior of the roller for the better adhesion on the sealing surface
- pH 0-14
Dimensions
- Thickness: 0.35 mm, 0.50 mm, 1.00 mm
- Width: Can be delivered as requested
KLINGER GRAPHITE RINGS K35
Compression molded graphite rings, pure graphite. Purity: 98% alt. 99.85%. Density according to the customer’s requests.
Specifications
- Suitable for high to very high temperatures, depending on the oxygen
- Also used in low temperatures
- Mainly a valve gasket
- Permanent resilience
- Extremely dense, properly compressed
- Suitable even in pumps
- pH 0-14
Dimensions
- Comes delivered in user defined dimension
